FREE BONUS SEEDS WITH ORDERS · DISCREET WORLDWIDE SHIPPING
← Grow guides

Cannabis Grow Light Guide: PPFD, DLI and Light Intensity by Stage

Watts on a label and guessing hanging heights won't tell you how much usable light your canopy actually gets. What matters to the plant is how much useful light reaches the leaves over the whole day. Here's how it works, without the heavy physics.

Three numbers worth knowing

  • PPFD is how much usable light hits the leaf right now, in µmol/m²/s. Think of it as brightness at one spot under the lamp.
  • Photoperiod is how many hours a day the light is on.
  • DLI (Daily Light Integral) is the total light delivered over the day, in mol/m²/day. This is what the plant actually responds to.

The math is simple: DLI = PPFD × light hours × 0.0036

For example, 500 PPFD for 18 hours gives about 32 mol per day. 800 PPFD for 12 hours gives roughly 35.

Targets by stage

StagePPFDLightDLI
Seedlings and clones200–40018/613–25
Veg400–60018/625–40
Flower600–90012/1226–39
Flower with CO₂900–120012/1239–52

These are starting points, not hard rules. If the room sits around 20 °C or the air is dry, the plant can't use maximum light. In that case, stay in the middle of the range.

For matching temperature and humidity at each stage, see our climate and VPD guide.

How to measure light

  • A PAR meter is the most accurate option. Measure at canopy height: center, edges and corners.
  • Phone apps with a diffuser give a rough estimate. For a home tent, that's usually good enough.
  • Manufacturer PPFD maps help at the start, but they're usually measured in ideal conditions. Real numbers are often lower.

The edges of a tent almost always get 30–50% less light than the center. That's normal, just keep it in mind when placing pots.

How to raise intensity

  1. Start at the low end of the range for your stage.
  2. Every 3–4 days, add 10–15% on the dimmer or lower the lamp.
  3. Watch the top leaves. If they look relaxed, keep going.
  4. Stop as soon as you see the first signs of too much light.

Signs the light is off

Too much light:

  • tops turn yellow or white while lower leaves stay green;
  • leaves fold upward like a taco;
  • growth slows even though feeding is fine.

Too little light:

  • the plant stretches with long gaps between nodes;
  • stems are thin and leaves are pale;
  • buds come out loose and airy.

Common mistakes

  • Going by watts alone. Two 200 W lamps can put out very different amounts of light.
  • Starting at 100% power. Seedlings and fresh clones suffer for it.
  • Forgetting the photoperiod. At 12/12 the plant gets a third less light than at 18/6 at the same brightness.
  • Breaking the dark period in flower. Even brief light during the night can throw photoperiod plants off their bloom.

To spread light evenly across every top, level the canopy with LST and a ScROG net.

In short

Measure PPFD at canopy height, multiply by light hours and check the table. Raise intensity gradually and watch the top leaves. The plant will show you when you've hit its limit.

Quick answers

How much PPFD does cannabis need in flower?

About 600–900 µmol/m²/s at 12/12 without added CO₂, and up to 900–1200 with CO₂. Seedlings need only 200–400.

How do I calculate DLI?

DLI = PPFD × light hours × 0.0036. For example, 500 PPFD for 18 hours gives about 32 mol/m²/day.

How do I know if my light is too strong?

The tops turn yellow or white while lower leaves stay green, leaves fold up like a taco and growth slows even with good feeding.